Wisconsin recalls

The recalled drain covers violate the entrapment protection standards of the Virginia Graeme Baker Pool and Spa Safety Act (VGBA), posing entrapment and drowning hazards to swimmers and bathers.

The elevator's StrikeLock hoistway door locking device can allow the elevator cab to move with a landing door open, posing a risk of serious injury or death due to fall and injury hazards.

The recalled bed rails violate the mandatory standard for adult portable bed rails because users can become entrapped within the bed rail or between the bed rail and the side of the mattress, posing a serious entrapment hazard and risk of death by asphyxiation. The bed rails also do not meet structural stability or retention strap requirements, posing a fall hazard. The bed rails' push pins and push pin holes are incorrectly sized, posing a laceration hazard. In addition, the bed rails do not bear the required hazard warning labels.

Failed Impurities/Degradation Specifications: Out of specification for specific impurity Tretinoin

For Immediate Release - BETHLEHEM, PA – APRIL 28, 2026 – B. Braun Medical Inc. is voluntarily recalling two lots of Lactated Ringer’s Injection, E7500, 1L, to the hospital/healthcare facility level. The product has been found to have particulate matter in solution.

Ghirardelli Chocolate Company of San Leandro, California is voluntarily recalling certain powdered beverage mixes because they have the potential to be contaminated with Salmonella. This action follows a California Dairies, Inc. milk powder recall due to a concern of potential Salmonella contaminati

Ferris Coffee & Nut Co., Grand Rapids, Michigan is recalling a single lot of Frederik’s by Meijer Vanilla Bourbon Trail Mix 9 oz. because it may contain undeclared wheat and soy. People who have an allergy or severe sensitivity to wheat or soy run the risk of serious or life-threatening allergic re

The recalled children's toys violate the small parts ban because the toy is intended for children under three years of age and the fence handles can detach from the toy, posing a deadly choking hazard.

The recalled baby loungers violate the mandatory safety standard for infant support cushions because the padding can obstruct an infant's breathing, posing a serious risk of injury or deadly suffocation hazard.

The baby loungers violate the mandatory standard for infant sleep products because the sides are shorter than the minimum side height limit to secure the infant and they do not have a stand, posing a fall hazard. Additionally, an infant can fall out of the enclosed opening at the foot of the lounger or become entrapped. Furthermore, the sleeping pad's thickness exceeds the maximum limit, posing a suffocation hazard. These violations create an unsafe sleeping environment for infants, posing a risk of serious injury or death.

The magnetic stick figures violate the mandatory standard for toys because they contain loose magnets posing an ingestion hazard to children. When high-powered magnets are swallowed, the ingested magnets can attract each other, or other metal objects and become lodged in the digestive system. This can result in perforations, twisting, and/or blockage of the intestines, blood poisoning and death.

When worn during high-intensity activities that generate a combination of heat, excessive friction, moisture and pressure, the socks can pose an injury hazard including burns.

The recalled delivery boxes violate the mandatory standard for consumer products containing button cell and coin batteries because they contain a lithium coin battery that can be easily accessed by children, posing an ingestion hazard. The packaging also does not bear the required warning labels for products containing such batteries as required by Reese's Law. If button cell or coin batteries are swallowed, the ingested batteries can cause serious injuries, including internal chemical burns, and death.

The recalled tower stools can collapse or tip over while in use and a child's torso can fit through the openings on the tower's sides, posing a risk of serious injury and death due to tip over, fall and entrapment hazards.

The recalled tower stools can collapse or tip over while in use and a child's torso can fit through the openings on the tower's sides, posing a risk of serious injury and death due to tip over, fall and entrapment hazards.

Weight plates can dislodge from the handle during use, posing a risk of serious injury due to impact hazard.

The recalled tower stools can collapse or tip over while in use, and a child's torso can fit through the openings on the tower's sides, posing a risk of serious injury and death due to tip over, fall and entrapment hazards.

The recalled products contain sodium hydroxide (lye), which must be in child-resistant packaging as required by the Poison Prevention Packaging Act (PPPA). The packaging is not child-resistant, posing a risk of chemical burns and irritation to the skin and eyes. The products also violate the labeling requirements for hazardous substances under the Federal Hazardous Substances Act (FHSA).

Philips has identified three software issues: 1. During a continuous CT (CCT) scan, there is the potential that the Gantry could remain at the current scan position after pressing Go. 2. Potential where the message of Previous Surview Exists Select Previous Surview? <Yes> or <No> should display but does not appear. 3. After performing Surview and planning the Brain Helical acquisition by setting Brain Area DoseRight Index to increase the dose, there is the potential that the Define Head Area option in the context menu is grayed out.

On lot of Sterile Circumcision Kits was distributed without the required sterilization process and is therefore not sterile.

The potential for repeated frames during HF-OCT pullback when using the Gentuity HF-OCT Console (software version 21.11 to 23.3.13) with the Vis-Rx and Vis-Rx Prime catheters. This correction is intended to ensure that users are fully informed of how to recognize, avoid, and mitigate this condition to maintain accurate longitudinal (length) measurements during OCT imaging.

Increased difficulty in installing the centrifuge bowl onto the centrifuge bowl holder. Improper installation may cause the centrifuge bowl to dislodge, resulting in a broken bowl during the prime cycle or treatment phase, leading to a delay in patient treatment and blood loss.

Due to a quality issue regarding the presence of burr on the finished cervical plate product.

Increased rate of out-of-specification endotoxin results.

Increased rate of out-of-specification endotoxin results.

Increased rate of out-of-specification endotoxin results.

Increased rate of out-of-specification endotoxin results.

Increased rate of out-of-specification endotoxin results.

Devices which did not meet internal quality specifications were inadvertently distributed.

During 3D acquisitions, lighter and darker patient images may be captured, which may result in less accurate 3D reconstruction. The variation of brightness is a result of a constant unregulated medium dose and the angular change of patient diameter caused by rotational acquisition. This may result in unintentional low-dose radiation exposure to a patient.