Connecticut recalls

Product contains undeclared Yellow #5

Product may be contaminated with Salmonella

Failed Tablet/Capsule specifications: Red dots inside capsule and melted capsule caused by oxidized Icosapent ethyl, the active ingredient.

The rivets used to support the swing seat can fail, posing a fall hazard to children.

The recalled dressers are unstable if they are not anchored to the wall, posing tip-over and entrapment hazards that can result in risks of serious injuries or death to children. The dressers violate the mandatory standard as required by the STURDY Act.

The recalled dressers are unstable if they are not anchored to the wall, posing tip-over and entrapment hazards that can result in risks of serious injuries or death to children. The dressers violate the mandatory safety standard as required by the STURDY Act.

The recalled helmets violate the mandatory safety standard for bicycle helmets because the helmets do not comply with the impact attenuation, positional stability, labeling and certification requirements. The helmets can fail to protect the user in the event of a crash, posing a serious risk of injury or death due to head injury.

The recalled magnet games violate the mandatory standard for toys because they contain loose high-powered magnets that fit within CPSC's small parts cylinder, posing an ingestion hazard to children. When high-powered magnets are swallowed, the ingested magnets can attract each other, or other metal objects, and become lodged in the digestive system. This can result in perforations, twisting, and/or blockage of the intestines, blood poisoning and death.

Mis-wired component-the improperly wired component can result in additional noise on the power supply output. Noise on the ultrasonic input circuit is not consistent with electromagnetic compatibility (EMC) standards and may decrease the overall reliability of the system and result in delay of treatment. It was discovered that additional serial numbers of ShockPulse generators may also have the mis-wired component. As a result, this is expanding the action to the additional impacted devices.

Behind-the-ear sound processer packaging label is different then included product.

Gelatin sealed woven polyester prostheses devices, designed for vascular repair, were incorrectly labeled with an additional month of shelf life. Device expiry should have been calculated from gel impregnation (date of manufacture) but it was incorrectly calculated from device packaging.

The potential of out-of-range results and an underestimation of the free protein S level in normal patient plasmas. The defect only affects normal-range values.

A potential weakness has been identified in the probe body, so that, in a specific production batch, liquid may leak from the terminal part of the casing near the cable.

Potential for rubber fragment detachment during use.

Potential for rubber fragment detachment during use.

The firm has identified that the battery runtime and cycle specifications contained in the devices Instructions for Use (IFU) need to be updated.

The firm has identified that the battery runtime and cycle specifications contained in the devices Instructions for Use (IFU) need to be updated.

There is the potential for the length of the trocar shaft to be too long.

Falsely depressed UAlb patient results may occur. Affected samples with any urine albumin concentration above the UAlb measuring interval >40.0 mg/dL may report values between 6.2 mg/dL and 40.0 mg/dL.

The potential for the needle tip to be dull/blunt, difficult to advance, and/or break.

The potential for the needle tip to be dull/blunt, difficult to advance, and/or break.

The potential for the needle tip to be dull/blunt, difficult to advance, and/or break.

Toric Implantable Collamer for correction/reduction of myopia in phakic eyes with astigmatism were labeled as 12.1 mm length but are 12.6 mm length lenses, so there is the potential for excessive vault, which may cause: Significant reduction of irido-corneal angles, Significant shallowing of anterior chamber, Patient discomfort, Elevated IOP/Angle closure, Unreactive pupil, Lens exchange/removal.

Ongoing investigations identified additional instances of the device Generator remaining in a blinking phase waiting to recognize the transducer. Damage to the transducer plug and/or generator receptacle may cause these issues.

Ongoing investigations identified additional instances of the device Generator remaining in a blinking phase waiting to recognize the transducer. Damage to the transducer plug and/or generator receptacle may cause these issues.

Ongoing investigations identified additional instances of the device Generator remaining in a blinking phase waiting to recognize the transducer. Damage to the transducer plug and/or generator receptacle may cause these issues.

Software defect, which allows the system to accept erroneous, non-monotonous calibrations for Spline-type assays. Cobas pro integrated solutions is an automated analyzer, intended for running qualitative, semi-quantitative and quantitative clinical chemistry and immunochemistry assays, as well as ion-selective measurements. When an erroneous calibration is active, the instrument fails to calculate new values and instead repeats the last successfully calculated result from any Spline-type assay for all subsequent measurements, leading to identical and erroneous patient and QC results. The defect could lead to patients receiving erroneous lab results, which could result in a remote risk of serious adverse health consequences. The following assays use spline type calibration and are affected by this issue: Cystatin C Gen.2, Ferritin Gen.4, Lipoprotein (a) Gen. 2, Lipoprotein (a) molarity, Vancomycin Gen.3, Kappa Free Light Chains Partner Channel, Lambda Free Light Chains Partner Channel, and fCAL turbo Partner Channel.

Under certain workflows, patient information shown in the viewer may not match the images displayed on Centricity Universal Viewer Zero Footprint Client (ZFP) with versions ZFP v6.0: SP11.6, SP11.6.0.1 and SP11.6.1 on systems with Patient Timeline installed,

Differential pressure (dP) sensor in Impella RP devices may malfunction, causing sensor values to drift.

Differential pressure (dP) sensor in Impella RP devices may malfunction, causing sensor values to drift.